Minecraft Wiki

除另有声明,转载时均必须注明出处若簡繁轉換出錯,請以遊戲內為準请勇于扩充与修正内容有兴趣逛逛我们的微博沟通交流,欢迎到社区专页需要协助,请在告示板留言

了解更多

Minecraft Wiki
Advertisement
Ic translate
此條目的(部分)內容需要翻譯。

你可以幫助我們來翻譯此條目,但請勿使用機器翻譯

Airlocks are structures effective at preventing water from spreading into buildings. The airlocks shown here will close in the event of flooding, but will not reopen until the player breaks them. The designs shown here are not true airlocks, but are simply watertight compartments to close in the event of flooding. Using a door is more like a true airlock.

Mechanics

Airlock Finished

一個已完成的空氣閘。按下按鈕會觸發粘性活塞將石春上的火炬移除,使沙落下。

Airlocks rely on the properties of the torch, sand, and water to function.

  • Torches can support other blocks, and they turn back into an item if the block it is attached to is removed or if it is exposed to water.
  • Sand will always attempt to fall and can be supported by a torch.
  • Water flows outwards, but will dry up if not connected to a block of still water.

When a torch with sand on top of it touches water, the sand drops and stops water flow in that direction. If torches are attached to any of the blocks above, then that torch will break as well. This will continue to the very last torch.

Construction

Design 1

An airlock requires only two components, a block affected by gravity (such as sand) and torches (regular or Redstone). When placing an airlock, be sure to think about choosing narrow passageways and choke points, so that less time is spent on the project. For a building with multiple entrances, multiple airlocks may be needed to achieve optimal dryness. Airlocks are usually built directly across the hallway. Most sand-based airlocks are only 1 block thick, due to the fact that only 1 layer of sand is needed to stop the water.

Determining the materials needed is simple enough. The number of torches is equal to the width of the corridor, and sand is equal to the width of the corridor times the height of the corridor. Optionally, a shovel and a pickaxe can be taken along, to speed up digging and to waste less time on mistakes.

For the first step, the hallway must have a ceiling height equal to the highest water level possible plus 1, to compensate for the torch. Also, each new column must be 1 block higher, as the torch is 1 block higher each time. A torch is placed on either wall at a level where water can contact it and there is enough space above to provide the required amount of sand to seal the chamber. Sand is now placed above the torch until the sand reaches the ceiling, or until it reaches the desired level.

(A 1 block wide hallway is complete at this step)

一個一格寬的空氣閘。

A passageway more than 1 block wide must be extended from wall to wall in a particular fashion. A torch is placed on the block of sand above the previous torch, and sand is placed above that. This process is repeated until the hall is waterproofed.

一個三格寬的空氣閘。

Design 2

Sugar Cane can be used as a type of airlock, though this presents the difficulty of growing it inside.

Design 3

Since the introduction of Pistons, they can be used to make much more compact airlocks using the same basic techniques. Piston-based airlocks are not restricted to using sand or gravel, but they may require redstone circuitry which tends to make them costlier and more complex than torch/sand or torch/gravel airlocks. A simple way to build one would be to make a piston system that is retracted when the current is stopped and then placing redstone across the passage.

Other Uses

Airlocks are one of the first completely environmentally reactive traps in Minecraft.

The use of Airlocks in stopping water flow can also be applied to the concept of controlled flooding, allowing one to flood an area until a certain water level or redirect it when those levels are reached.

The torch system could also trigger sand falling into a room, where a hole in the ceiling then opens up and lava then pours in to cancel out the water. As long as it involves the movement of sand and water, it's quite an effective trigger system.

Trivia

Advertisement