然而,最好的放置红石火把的间距是每13个方块放置一个,这可以保证亮度等级在8及以上,并且确保每个充能铁轨都有效.为了美观,it might also be desirable to space out powered rails every 39 blocks with 3.1% speed losses, or to space them out at 1 every 36 blocks with torches 1 every 12 blocks for the same speed loss as 1 every 38 blocks.
An optimal use requires the synchronization of minecart movement and powered rail placement; moving a powered rail a single block forward or back along a track can make a significant difference. This is because the momentum of a minecart is increased per tick (=1/20 of a second) the cart spends on a powered rail (by 0.9 m/s for occupied carts). When a cart travels at the maximum 8 m/s on a straight track, it alternately spends either 2 or 3 ticks on each block. For an optimal placement, the powered rail must be put where the cart spends 3 ticks,否则有三分之一的加速将被浪费.
A diagonal track is a track that consists of the pattern 'left corner' attached to a 'right corner' attached to a 'left corner' ... and so on. When minecarts travel on a diagonal track, the camera is held steady in the diagonal direction and the minecart visually travels diagonally along the track as well. The speed limit of minecarts is actually 8 m/s per cardinal axis, thus when traveling on 2D tracks, the cart will travel 8 m/s in both cardinal directions of travel to result in a net vector of about 11.3 m/s or the square root of 128. With a 3D track you travel as fast as 13.85 m/s or the square root of 192.
Because of this difference, there is also a difference between the optimal spacing of powered rails when used on a 2D track when compared to straight travel on flat terrain. This is currently undetermined to high accuracy but is roughly 1 every 52 blocks.[3]
There is also a difference in unmanned or storage mine carts so it is advisable to use a shorter interval if these carts will be used on the track.
It seems as if the optimal Powered Rail placing interval to make storage mine carts move is 4 (1 Powered Rail every 4th block). Compared to shorter intervals the reduction in speed is minimal. The maximal possible interval seems to be 9 as the minecart will not reliably reach its destination when using higher intervals.
探测铁轨的用处
主条目:Detector Rail
A Detector Rail will power 4 adjacent blocks and 2 blocks below it when a minecart, occupied or empty, is on it. This makes it possible to activate powered rails inline without redstone torches or wiring.
A detector can be used to activate adjacent powered rails. However, if the detector is used to activate more than two or three (depending on approach speed) powered rails, the rails will deactivate before the minecart reaches them, bringing the cart to an immediate stop.
One-way powered rail lines can be created by placing a detector rail before a powered rail. This way, occupied carts will only be boosted if they are traveling the proper direction. Carts going the "wrong" way will be brought to a stop because the powered rail is inactive.
Although inefficient, A two-way rail line can be created by placing detector rails on either side of the powered rail.
Alternately, placing powered and detector rails on a 1×1 slope will not propel a cart more than 3 blocks upward if there is not enough initial momentum. The cart will lose too much speed on the incline, meaning it can't make it from the detector rail to the powered rail before the powered rail returns to the "off" state. If the cart is in a train of two or more carts, the last car in the train will become stuck instead.
A detector rail could also be used to activate an event based on a cart's location. For example, a fail-safe can be created to release a stopped cart in order to prevent a collision with an arriving cart. The arriving cart passes over a detector rail, activating a powered rail that boosts the resting cart away.
Curved power rails only exist in the case where the final direction is towards the east (with the powered rail appearing in the north-south orientation), or in a T-junction where one path faces east along a north/south track.[4][5] It is possible to make a one-way curved railway using power rails, but not a bi-directional one.
When placing rails, regular rails prefer to curve towards the powered rail. In cases such as these, the south-west rule applies.
A cart traveling on a powered rail that collides with an object (wall, single block, player, other cart) will reverse direction. It will not reverse direction if it collides with a translucent block, such as Stone Slabs or Glass. If a track including powered rails is bordered by blocks acting as "buffers", the cart will indefinitely continue back and forth along the track. Having carts interact with each other on a short track designed this way can be used to chain multiple carts together as a "train". Once aligned, they will all move together at relatively the same speed.
How far the charge passes down adjacent rails is independent of the length of redstone wire. Even if the rails are connected to a redstone torch by 15 blocks of redstone dust, the 8 adjacent rails will still be powered normally despite the fact that they should be out of range for the torch.
自动轨道机构
停止点
It is possible to make points in your track where a cart is stopped and then jumpstarted again by player input. This can be useful for creating checkpoints to certain sites of interest in your world. This can be done by using two powered track pieces on a one block incline, by having the first powered track piece going down, with the second powered track piece at the bottom and a button placed alongside the second powered track piece, so that the button is directly above the track. You can see an animated example of this stop point if you click on the image to the right.
Animated Gif of a stop point. Click for the animated version
When the cart comes to this point it will stop On the incline, allowing the cart to use gravity to start the boost when the button is pushed. Players can then either stay in the cart and carry on to the next stop, or leave the cart at the station for themselves/other players to use later.
A "two-way" stop can be made by combining two of the normal stops with a detector rail in between. This will pause a minecart travelling in either direction and allow them to be restarted by pressing a button.
To create a simple initial boost device using 2 powered rails, dig a hole 1 block deep and 2 blocks long. Place the powered rails inside the trench, connect one end to the track that you wish the mine cart to exit. Finally place the mine cart on the powered rail. Once power is applied to the rail the minecart will be boosted out.
微型系统
启动器
Launchers, stations or exits all refer to a point in the system where a rider can safely enter or exit a minecart. They generally use a button to launch the cart.
A simple minecart launcher
This first design uses a button, a few powered rails, a bit of redstone wire, and a redstone torch. The button powers the powered rail which launches the cart away from the solid block behind it. In this style of launcher, it is important for an incoming minecart to make it all the way up to the back block so it can easily be launched again.
A launcher with cart dispenser
This second design is essentially the same as the first. A dispenser replaces the solid block behind the last powered rail. The dispenser will launch the minecart just like the solid block, but creates a convenient place to store extra minecarts. To activate, use the button behind the dispenser and a minecart will pop onto the rail and be ready for use.
See also: Tutorials/Minecart start booster
Rider Detection
Players will tend to want to detect whether a cart has a player in it or not as empty carts will clog a rail system. This is referred to as rider detection.
Trip wire based design
A trip wire based design is quick to set up and will reliably detect a player. However, it won't detect some non-player mobs, specifically 'short' mobs (wolves, spiders, pigs, etc.).
To build, a trip wire is attached to hooks one block above the track. Two blocks further is a junction which is set by default to turn empty carts back to the station. An empty minecart will not trigger the trip wire and be sent back, while an occupied minecart will send a short pulse to the junction and continue along the rest of the track.
Depending on orientation, the signal may need to be inverted with a redstone torch. Although the torch will add delay, it is minor and shouldn't affect the results. This design assumes the minecart is moving at top speed. If your minecart is moving slower than that, you can either add delay to the wire using repeaters or increase the speed of the minecart with a booster just before the trip wire.
A momentum based design
Another method to check for a rider is to take advantage of the change in speed of the cart, as an empty cart slows down more quickly. In this design, a minecart will create a pulse when it passes the detector rail. If the minecart is empty, it will get to the turn just as the signal does and be sent back. If the minecart has a rider, it will get to the turn before the signal and be able to continue on. This design requires the track to be set by default to let the cart through.
空车
An overflow pile for empty carts
When an empty cart is detected, generally it's a good idea to send it into an overflow pile. An overflow pile is a drop of two or more blocks with a rail at the bottom. When carts are boosted into the hole, they will snap to the track, regardless of how many carts are already on the track. This pile should be placed where the carts can be collected, either close to a station or in a maintenance area. It is important to boost carts to full speed just before they are dropped to ensure they don't become stuck on the end of the track and eventually back up the system.
Another variant of this method is to replace the rail at the bottom with a cactus, thus destroying minecarts that fall in. Placement of a hopper next to the sand on which the cactus is placed then allows saving of at least some of the carts.
加速器
Two styles of speed boosters
Boosters are a method used to prevent carts from slowing to a stop on a track. Because carts will eventually slow to a halt on level track, and very quickly turn around on regular rail track whilst uphill-bound, boosters are a method of assuring one's cart keeps moving. Boosters accelerate carts to a terminal velocity of 8 m/s, as they use powered rails, and help effectively counter the forces of friction and gravity on the acceleration of the cart.
Boosters are simply a single powered segment of powered rail, powered through detector rails, redstone torches or levers next to them. Refer to the diagrams to the right.
Players generally keep the distance between boosters uniform, although these distances vary by player. One common, and according to many the most efficient, distribution of powered rails is to place powered rail every 38 blocks on level ground. An easy way to place a lot of track using this count without needing to keep track of each rail is by dividing the rails into stacks of 37, as shown on the right. Approximately 1 out of every 3 rails will need to be powered to travel uphill due to gravity.
Junction
Stations often have one line leading to one destination. Multiple destinations require multiple lines. A junction is a fork in the track where the rider can select which destination he wishes to visit.
Two-way junction
This design uses a lever to switch the track and the powered rail will become powered after a preset delay. The detector rail starts the delay. In this design, the lever will always point towards the selected destination regardless of direction.
Four-way junction
A junction that has multiple destinations can be set up by expanding the junctions. In the design to the right, the rider is given much more time to select his destination than a two-way junction. He can select any destination by first selecting left or right, then forward or backward. This design doesn't scale well but can be used in sequence to create any number of destinations.
Multiple Destination Selector
There are many, many styles of minecart destination selectors. Most are modular, meaning they can be extended to include more destinations. An RS-NOR latch array is often used to select a destination as these latches have a designated reset line (as opposed to a t-flip flop which only has one input).
This design was selected for its simplicity and for its ability to be expanded with relative ease. One of the buttons on the selection panel is a designated reset line since additional input doesn't clear the previous selection; that is to say, a player can select more than one destination with this design (although a launched minecart will take the left-most of the selected destinations).
The following design is heavily influenced by the previous but uses a different RS-NOR latch design involving pistons. It has a reset integrated in the selection such that a new input will clear a previous one. By removing the designated reset line of the previous version, it allows for an additional station in a similar amount of space.
Example Of A System Incorporating Some of the Basic Parts
This system consist of a "Launcher", a different mechanism for "Empty Carts", a "Junction" and a "Booster"
System works on tripwire.
The empty minecart is always moving in circles awaiting a passenger. (Empty cart compenent is not needed any longer)
When a passenger is present, tripwire will activate and the rails will switch routes for a few seconds and cart will move away from the station. (Launcher, booster and junction all infused into a simple redstone circuit.)
故障排除
When a track system isn't working properly, it can be difficult to fix for someone unfamiliar with redstone and rails.
Common solutions include:
Changing the delay of circuit by adding a repeater or moving a detector rail to trigger earlier.
Changing the speed of the minecart by adding powered rails or moving the current ones further away.
Checking that powered rails are powered properly.
Turn the design around, as direction can affect how it works. Generally this isn't the issue, but it's good to rule it out.
Searching on the minecraft forums can help. If you need to create a new post, be sure to include the direction you're working (the F number), as directionality can be a factor in the design.