Minecarts behave in a unique manner when running alongside one another - they accelerate rapidly. This effect is used to create boosters. A booster consists of a short track with another minecart placed next to the track you want to boost. The two tracks will have one or more squares of contact. When your minecart is next to the other cart, they will both accelerate. There is a maximum speed (8m/s, 1 block = 1 meter). If a cart runs for a prolonged period, glitches may occur. A good way to avoid this is to make sure that no cart is continuously being boosted over a long period of time (caused by a loop without stops).
Example of two boosters in a loop. The first booster loop is continuously working, which will eventually cause glitches. The second booster loop provides a pause by stopping every cart, every iteration. This creates a more reliable system.
Boosting Principle
Do take note that the methods above are not the only configurations that can be used to boost a minecart. Instead, rely on the following principle when designing booster systems:
- A minecart pair will boost when they are side-by-side.
- As long as the carts are side-by-side, they will continue to accelerate, until reaching 8m/s.
- It is ideal to have the booster cart reset itself after use (i.e. return to its original position) so it can be used again right away, but this is not required.
- The south-west rule or other track layout techniques can be used to accomplish this reset.
- A cart will slow down if it approaches a neighbor cart head-on (e.g., not off of a slope or curve), and a proper boost will not be accomplished. Keep this in mind when designing two-way systems. The following diagrams illustrate this concept:
Good (will result in a boost)
Bad (will slow down cart)
Booster types
Two-way manual-reset
This is probably the simplest booster you can build. It is easy to build and easy to understand. It is also very compact, taking up as little extra space as possible.
This booster only requires "manual reset" if you want to go though the same direction twice. After you go one way, this booster will be ready for boosting the opposite direction. If you never travel the same direction twice in a row (you always come back from where you've gone), then this booster might be good enough for you.
File:Two-way manual-reset booster.png
Two-way corner manual-reset
This example demonstrates a two-way manual reset booster. The booster only requires a manual reset should you want to go the same direction twice. It is an excellent solution for those who prefer to have minimal alterations made to their terrain.
One-way auto-reset (south-west rule)
These are two possible configurations for one-way resetting boosters based on the south-west rule. The one on the left is a south→north booster, and the one on the right is a west→east booster.
One-way auto-reset (based on inclination)
This booster uses a raised auto-reset loop, so that it can be built in any direction. The booster minecart will go through the loop and fall onto the inclined track, going back to the starting position.
One-way auto-reset (reduced reset loop)
This booster is just like the previous booster but only requires three tracks for the auto-reset loop. It takes a couple more steps.
First build the tracks like this. In order to bend the third track around so that it resets, you need to add a block above the track like this.
Then place a track on top of the block. That will bend the third track into its proper placement.
The last step is to remove the block.
One-way auto-reset (leveled and omnidirectional)
This booster uses a simple loop that throws the cart back onto the track, since the track is angled it hops onto the track and continues in a straight line, ignoring the S-E rule that applies when running into perpendicular tracks.
Two-way auto-reset
Here is an example of a two-way resetting booster that is direction-independent (its cardinal direction doesn't matter):
Two-way auto-reset compact design
Here is an example of a two-way resetting booster that is direction-independent this design is a little more compact.
Two-way auto-reset efficient design
Here is yet another two-way gravity powered auto-reseting booster - the lower cart pictured (the booster) sits in the center of a symmetrical section of track, and will always come to rest at that point. This may be the most efficient when it comes to amount of iron that is needed to make it. (credit goes to alfadark on reddit.com)
Uphill auto-reset booster
This is a simple, compact and effective way of going uphill. It won't boost you downhill, but gravity will handle things for you there.
- This is your main track. You want to build a booster here.
- Dig a 2x2x1 hole containing your main track.
- Rebuild the two pieces your main track inside the hole (like a "V" letter). Then, start building a booster track.
- At the top end of the booster track...
- ...remove the last track piece...
- ...and put a block there. This way, the booster minecart will hit that block and go back down to the starting position.
- Your finished track.
Double Booster
This is a way that you can put two carts into one which is believed to more than double the distance you can get out of your booster.
NOTE: this is a glitch that might get fixed in the future, which might cause you to redesign your track system.
In order to make the double booster, you need to put a block, then a piece of track (may require two tracks in order to align the cart correctly) above the cart to be doubled and place a cart on that track.
Next remove the block. This will drop the first cart into the second merging them. At least until they fall off the track.
you can also ride "them" and they'll move nearly forever if there is no dead end. also moves slower off track and can move through water.















