A logic gate can be thought of as a simple device that will return a number of outputs, determined by the pattern of inputs and rules that the logic gate follows. For example, if both inputs in an AND gate are in the 'true'/'on'/'powered'/'1' state, then the gate will return 'true'/'on'/'powered'/'1'.
There are many different kinds of logic gates, each of which can be implemented with many different designs. Each design has various advantages and disadvantages, such as size, complexity, speed, maintenance overhead, or cost. The various sections will give many different designs for each gate type.
Concepts[]
The output of each logic circuit reflects the state of its inputs at all times (though possibly with some delay incurred by the circuit).
- Swapping inputs
- For most of these gates, A and B can be swapped without changing the output.
- Swapping the inputs of the IMPLIES gate will affect its output, and the NOT gate has only one input.
- Stacking inputs
- The AND, OR, and XOR gates can each be used in arrays to perform their operation on more than two inputs, by combining two inputs at a time, then combining the results with each other and/or other inputs. For these gates, the order in which the inputs are combined doesn't matter.
- When an XOR gate is combined in this way, its output is on when an odd number of inputs is on.
- Choosing a logic gate
- When unsure which logic gate to use, try building a table like the one down below but with just one row of outputs. List the known inputs coming in and the possible combinations of power, and for each combination write down what the output should be for the structure to work. Then compare that to the table on the right and see which gate matches the desired outputs.
- If the the output needs to change when the input is stable, or needs to be remembered after the input has ended, the player may also need to look at pulse circuits or memory circuits.
A | ON | ON | off | off | Question Answered |
---|---|---|---|---|---|
B | ON | off | ON | off | |
A AND B | ON | off | off | off | Is A and B on? |
NOT (A IMPLIES B) | off | ON | off | off | Is A on and B off? |
NOT (B IMPLIES A) | off | off | ON | off | Is B on and A off? |
A NOR B | off | off | off | ON | Are both inputs off? |
A | ON | ON | off | off | Is A on? |
A XOR B | off | ON | ON | off | Are the inputs different? |
NOT A | off | off | ON | ON | Is A off? |
A XNOR B | ON | off | off | ON | Are the inputs the same? |
B | ON | off | ON | off | Is B on? |
NOT B | off | ON | off | ON | Is B off? |
A NAND B | off | ON | ON | ON | Is either input off? |
A IMPLIES B | ON | off | ON | ON | If A is on, is B also on? |
B IMPLIES A | ON | ON | off | ON | If B is on, is A also on? |
A OR B | ON | ON | ON | off | Is either input on? |
Logic gate[]
A logic gate is a basic logic circuit.
NOT gate[]
A | ON | off |
---|---|---|
NOT A | off | ON |
A NOT gate (), also known as an inverter, is a gate used when an opposite output is wanted from the input given. For instance, when the switch, or input, is set to "on", the output will be toggled to "off", and when the switch is toggled to "off", the output will be toggled to "on".
- Torch Inverter
- 1-wide, flat (horizontal only), silent, tileable
- circuit delay: 1 tick
- The torch inverter is the most commonly used NOT gate, due to its small size, versatility, and easy construction.
- One drawback of the torch inverter is that it will "burn out" if run on a clock cycle faster than a 3-clock (3 ticks on, 3 ticks off). A burnt out torch inverter will turn back on after it receives a block update.
- Subtraction Inverter
- flat, silent
- circuit delay: 1 tick
- The subtraction inverter offers little advantage over the torch inverter except that it can run on a 2-clock cycle without burning out. Faster clocks will not work though — the comparator simply won't react to them.
- Variations: The powered lever can be replaced with another always-on power component (e.g., redstone torch, block of redstone), or with a full container if a power component would be inconvenient in that location.
- The repeater is required to ensure the input signal is strong enough to overcome the comparator's rear source, but can be removed in a number of ways. If the input power level is known (because the circuit design is fixed, so it can be calculated), the repeater can be removed by replacing the powered lever with a container which will produce the same power level. Alternatively, the repeater can be removed if the output continues to a length of redstone wire which will reduce the subtracted signal enough that the signal is inverted eventually.
- Instant Inverter
- instant
- circuit delay: 0 ticks
- The instant inverter is a basic building block of larger instant circuits.
- The "ground" version has the largest volume, but is shorter and fits easily with flatter circuits. The 1-wide version is the smaller in total volume and 2-tileable.
- Behavior (i.e., how it works): An instant inverter has two functional elements, and a piston, or pistons, that activate them:
- a constant power source with output that can be instantly powered off (but powering it on takes time): either a redstone block that ceases to provide power as soon as piston starts moving it (within the same tick the piston receives or loses power) or a solid block in front of a powered repeater or comparator, powering redstone dust; as soon as the block starts moving the dust is unpowered.
- a signal line with output that can be instantly powered on but not necessarily off, its input delayed by and sustained for 2 ticks. The "instant on" is achieved by the dust-cut technique: a solid block placed against edge of a block over which a redstone line is running, disconnects that line from line below. Start of motion of that block instantly reconnects the line and provides power. The delay is achieved by running the input through a 2 tick repeater, two torches or similar means. That means, when power appears on input, the block moved by piston is able to cut the line before signal passes through the delay. With input unpowered, the output is instantly activated and the line still provides power "stored" in the repeater for two ticks, which time is sufficient to reactivate the constant power source from previous point.
- Piston, or pistons, to move the block/blocks activating the elements from point 1 or 2.
Schematic gallery: NOT gate
OR gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A OR B | ON | ON | ON | off |
An OR gate () is a gate which uses two or more inputs and whenever any input is "on", the output is also "on". The only time the output is "off" is when all inputs are "off". Note that since the OR operation is associative and commutative, OR gates can be combined freely: The player can compare huge numbers of inputs by using small OR gates to collect groups of inputs, then comparing their results with more OR gates. The result will not depend on the arrangement of the inputs, or on which ones were combined first.
The simplest version of the OR gate is design A: merely a wire connecting all inputs and outputs. However, this causes the inputs to become "compromised", so that they can only be used in this OR gate. The introduction's example, using a solid block instead of wire, does not suffer the same hazard.
If players need to use the inputs elsewhere, the inputs need to be "isolated", by passing them through a block as above, or a device such as a torch or repeater. Torches yield version B. Note that this is in fact a NOR gate with an inverter on the output.
Version C isolates the inputs with repeaters. It can be expanded horizontally up to 15 inputs. Besides the isolated inputs, it is one tick faster than B. Additional repeaters can be used to add new groups of inputs, or to strengthen the output signal. This design is more expensive, as each repeater costs 3 redstone dust to craft (along with smooth stone).
Version D is a 1-wide version designed for vertical use, such as in walls. The repeater serves to isolate the outputs from the inputs. This version can only take two inputs, though of course the inputs can be stacked with multiple gates.
Version E utilizes the properties of light-transparent blocks: glowstone, and upside-down stairs or slabs. These send signals up, but not down. It is expandable, like design C.
Schematic gallery: OR gate
NOR gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A NOR B | off | off | off | ON |
A NOR gate ( or ) is the opposite of the OR gate. Whenever at least one switch is toggled to "on", the output is toggled to "off". The only time the output is "on" is when all inputs are toggled to "off". This gate also uses two or more inputs.
All logic gates can be made from some combinations of the NOR gate.
In Minecraft, NOR is a basic logic gate, implemented by a torch with two or more inputs. (A torch with 1 input is the NOT gate, and with no inputs is the TRUE gate, that is, a power source.)
A torch can easily accommodate 3 mutually isolated inputs, as in design A. Design B goes to greater lengths to squeeze in a fourth input. If more inputs are necessary, it is simplest to use OR gates to combine them, then use an inverter (NOT) at the end. It is also possible to combine OR and NOR gates, by using the inversion of OR gates as inputs to NOR gates.
For inverted output when A is OFF, use redstone torch for B and result is:
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A NOR B | off | off | off | ON |
Schematic gallery: NOR gate
AND gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A AND B | ON | off | off | off |
An AND gate () is used with two or more switches or other inputs. The output is toggled to "on" only when all inputs are "on". Otherwise, the output will remain "off".
In reality, the usual implementation is a NOR gate with inverted inputs (). Taking the inputs and , the first two torches (at the top and bottom of Schematic (A) below) invert them into and . The redstone wire between these torches serves as an OR gate, and is therefore in state , which can be interpreted as by De Morgan's Law. Finally, the third torch (the center-right one) applies a NOT to that statement; thus it becomes .
A 3-input AND gate is shown, but, like OR gates, AND gates can be freely "ganged", combining groups of inputs and then combining the results.
A typical use for an AND gate would be to build a locking mechanism for a door, requiring both the activating button and the lock (typically a lever) to be on.
Piston AND gates act similarly to a "tri-state buffer", in which input B acts like a switch, connecting or disconnecting input A from the rest of the circuit. Such designs have one input feeding a circuit, which is opened or closed by a sticky piston driven by the other input. The difference from real-life tri-state buffers is that one cannot drive a low current in Minecraft.
Schematic gallery: AND gate
NAND gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A NAND B | off | ON | ON | ON |
A NAND gate ( or ) turns the output off only when both inputs are on, the reverse of an AND gate. All logic gates can be made from NAND gates. As with NOR, large numbers of inputs are probably best handled by stacking up AND gates, then inverting the result. By De Morgan's Law, is identical to .
All logic gates can be made from some combinations of the NAND gate.
Schematic gallery: NAND gate
XOR gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A XOR B | off | ON | ON | off |
An XOR gate (, or ) is a gate that uses two inputs and the output is toggled to "on" when one switch is "on" and one switch is "off". XOR is pronounced "zor" or "exor", a shortening of "exclusive or", because each input is mutually exclusive with the output. It is useful for controlling a mechanism from multiple locations. Because of these properties, XOR gates are commonly found in complex redstone circuits. In some cases, it is possible to get an OR gate output and an AND gate output on different channels. Design F is composed of AND gates, OR gates and NOT gates. The whole circuit is , which can be further simplified into (or, equivalently, ).
A useful feature is that an XOR (or XNOR) gate will always change its output when one of its inputs changes, hence it is useful for controlling a mechanism from multiple locations. When controls (such as levers) are combined in an XOR gate, toggling any control will toggle the XOR gate's output (like a light bulb controlled by two light switches — players can flip either one to turn the light on or off, or either of which can always open or close a door, or turn some other device on or off.
Like AND and OR gates, XOR gates can freely be "stacked" together, with gates gathering groups of inputs and their outputs being gathered in turn. The result of XORing more than two inputs is called "parity" — the result is 1 if and only if an odd number of inputs are 1.
Design D is tiny, but only useful if players want the levers to be fixed to the circuit. The shaded block indicates the block the levers and the lit torch are attached to, along with the block that one is resting on.
Design F is the most widely used of the torch-only designs, but newer components can do much better. Design H uses pistons, and is both faster and more compact.
Beyond torches and pistons, various diodes can be used to produce fairly compact and cheap XOR gates. Design I can have its input repeaters coming in from either side or underneath, changing its size accordingly to fit tight spaces. Design J uses transparent blocks for a cheaper option.
Schematic gallery: XOR gate
The introduction of the comparator allows for several variations of a new design, the "subtraction XOR gate", which is flat, fast and silent (also easy to remember). The cons in Survival mode is that making comparators requires the access to the Nether to obtain nether quartz.
Each input is the same distance to the rear and side of the comparator closest to it, so will suppress its own signal there, but travels farther to get to the side of the further comparator, so won't suppress its signal in the further comparator. Only if both inputs are on will both comparators get suppressed by a side input.
However, that is only true if the inputs are the same power level (or at least not different by more than 1), otherwise one signal could overwhelm the other's attempt to suppress its signal. If this circuit is sure to receive inputs of the same power level (because the system it's part of has been designed that way), then the "basic" version can be used. Otherwise, some method should be used to ensure the inputs are equal — for example, with repeaters (the "repeated" version) or with torches (the "inverted" version).
Schematic gallery: subtraction XOR gate
XNOR gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A XNOR B | ON | off | off | ON |
An XNOR gate ( or ) is the opposite of an XOR gate. This is commonly referred to as "if and only if" ("iff" [sic] for short), "bi-conditional", or "equivalence". It uses two inputs. When both switches are in the same state (both switches are "on" or both switches are "off"), then the output is toggled to "on". Otherwise, if the switches differ, the output is toggled to "off". Similar to the XOR gate, when either input changes, the output changes.
An XNOR gate can be built by inverting either the output, or one input, of an XOR gate.
Design A is a pure-torch design. If external input isn't needed, the back-facing torches can be replaced with levers, yielding B. Design F is larger but highlights the logic, while I is an inverted variant of XOR gate H. Note that the output inverter can also be placed in line with the rest of the gate, or even in a pit attached to one of the output redstone's support blocks.
Schematic gallery: XNOR gate
IMPLY gate[]
A | ON | ON | off | off |
---|---|---|---|---|
B | ON | off | ON | off |
A IMPLIES B | ON | off | ON | ON |
An IMPLY gate (A → B) turns on either if both inputs are on, or if the first input is off. Unlike the other gates here, the inputs are not interchangeable; it is not commutative. This represents material implication or a conditional statement, "if A then B", or "A implies B". The output is off only if the antecedent A is true, but the consequent B is false. It is the logical equivalent of B ∨ ¬A, and the mathematical equivalent of A ≤ B.
Design C has a speed of 2 ticks if output is 1, but 1 tick if the output is 0. Similarly, the other designs take 1 tick if the output is 0, but are immediate (and not isolated) if the output is 1. If the player must synchronize (or isolate) the output, consider placing a 1-tick repeater in front of the "fast" input (input A for C, input B for the others).
Schematic gallery: IMPLY gate
Gallery[]
Video[]
See also[]
- Logic gates on Wikipedia